Om alle inhoud te kunnen zien hebt u de actuele versie van Adobe Flash Player nodig.
Home Guitar Builds My Marshalls Marshall Footswitch mod Marshall front panel mod Marshall amp mods Mars amp mods 2 Marshall Divo inst Marshall Divo 2 Marshall Tubes Marshall Midi programming Airbrush Cat CT660 Truck Cat CT660 build 1 Cat CT660 build 2 Cat CT660 build 3 Cat CT660 build 4 Cat CT660 build 5 Cat CT660 build 6 Cat CT660 build 7 Cat CT660 build 8 Cat CT660 build 9 Cat CT660 build 10 Cat CT660 build 11 Cat CT660 build 12 Cat 385C LRE Cat385 underc. Cat underc2 Catunderc3 Cat underc4 Catunder5 Cat under6 Cat upper1 Cat upper2 Cat upper3 Cat upper4 Cat upper5 Cat upper6 Cat upper7 Cat upper8 Cat upper9 Cat upper10 Cat upper11 Cat upper12 Cat upper13 Cat upper14 Cat385 Hydr & Elec1 Cat385 Hydr & Elec2 Cat385 Hydr & Elec3 Cat385 Hydr & Elec4 Cat385 Hydr & Elec 5
Cat CT660 build 4
On the left you can see that the holes fot the light are cut out in the side pieces of the bumper.On the right you can see the licence plate holder, and the holder for the heavy transport plate.
On the left you can see a over view of the bumper with the license plate and the heavy transport plate in place.On the right you can see the bumper mounted to the chassis of the truck.
Above you can see some side views of the bumper.15 Januari 2016:Next thing to make are the holders for the lights in the bumper.
Above some pictures of the truck next to my Cat385 CLRE excavator.16 Februari 2016:
On the left you can see that I made the outside dimensions out of black pvc.On the right you can see how it's going to be placed in the bumper.
On the left a picture of the real truck.
On the left you can see that I made the lenses out of a electronics part of a lamp holder.On the right the lenses are placed on the holder.
On the left you can see the fog light lit,on the right you can see the curve light lit.
And the same in the dark,at the back side the led's are going to be covered at the final assambly,so there won't be ane light coming from the backside.
And here you can see the assembly glued into the bumper.
And this is how it looks at daylight.
And in the dark.27 Januari 2016:
On the left you can see the hinge that is attached to the bumper,and on wich the hood is going te be attached,so it can be tilted forward like on the retruck.On the right you can see the frame that I made, on wich the hood is going to be constructed.
On the left you can see the first platework cut out from 0,5 mm brass plate,in the middle is a section that is going to be lower then the outside.On the right you can see the plate being soldered on the frame.
On the left you can see that the gap between the inside and outside is closed.On the right youcan see that the sides of the hood have been placed.
On the left you can see that the gap between the top and side is closed.On the right you can see the hood tilted to the front.04 Februari 2016:
On the left you can see that I placed some bended strips on the side of the hood,on wich the fender is going to be soldered.on the right you can see the gitter that I made on the sides of the hood.
On the left you can see the first part of the fender soldered in place.On the right you can see the front part soldered in place.
On the left you can see that I made the profile on the front of the fender.On the right you can see a picture of the original truck,and the profile on front of the fender.
On the left you can see the side of the fender is finished .
On the left you can see that part of the fender is cut out to make place fot the hood locks.On the right you can see the lower fender part cut out also.
Above you can see the construction of the lower fender part.